TP-Link Router Login – tplinkwifi.net

Posted on December 29, 2020 by router

To access the router at any time for configuring its settings or managing its other functions, TP-link router login to its web based interface – admin page is required from any wired or wireless Wi-Fi connected device – may it be computer, laptop or a smartphone.

To get through TP-Link Router login and access Admin Panel, follow these guidelines below:

Have a computing device connected to the TP-Link router Network, either wireless by the way of Wi-Fi network or adjoining an Ethernet cable.
Get to an accessible and supporting web browser.
Follow TP-link router login by inputting tplinkwifi.net setup in the address bar of the browser.
Or follow the either way through Setup Your tplink Router login by keying in Router’s default IP address 192.168.0.1 or 192.168.1.1 other than tplinkwifi.net.
Immediately a Login page appears, to grant you an access to TP- link router login by entering the login credentials.
Key in desired TP-link router login detail as admin for username and password for password.

Enter the above default TP-link router login credentials if you did not change it while former TP-link router login or configuration.
If you do not know your default TP-Link router login fills, locate them from a label at the side or below the TP-Link Router.
You directly set into TP-Link router’s Admin interface.

The TP-link router admin interface is a settings page from where it is possible for you to change different settings of your router along with the password of your Wi-Fi/wireless network and the TP-link router login password accountable for tplinkwifi.net setup Login.

To Change The Wireless Password of the TP-Link Router WiFi Network;

Changing the password of the TP-Link WiFi network is desirable to avert unwanted or undesirable router access using the default credentials -default WiFi SSID and Password. This creates a secure and safe network across your devices.

Go through TP-link router login by inputting tplinkwifi.net in the address bar of the browser.
Set user identification as explained above to reach the Admin Panel of the TP-Link Router.
Hit clicking on Wireless on the admin page.
Opt for Wireless Security option.
Scroll down to select the WPA-PSK/WPA2-PSK section.
Create a new key of your own in the displayed PSK Password field.
Save the changes you made to secure your router.

To Change the TP-Link Router Login Password – tplinkwifi.net login;

Go through TP-link router login by inputting tplinkwifi.net in the address bar of the browser.
Set user identification as explained above to reach the Admin Panel of the TP-Link Router.
Key in desired TP-link router login detail as admin for username and password for password.
You will now access the TP-link router admin interface setup page.
Locate the Management option on the setup interface.
Select the Access Control option.
Opt for the Password option and click on it.
Key in your old password when prompted.
Create the new TP-link router login password.
Assign the same whenever prompted.
Save/Apply tplinkwifi.net login password.

Configure TP-Link Router as a Wireless Access Point – TP-link Router Setup

Posted on December 22, 2020 by router

Configuring your TP-link router as a wireless access point can generate a wireless local area network – WLAN by the way of acting as a portal for other wireless devices to connect to the network across wired cable connections. You can build up the connection across adjoining your main router to the tplinkwifi.net setup wireless router over a LAN port instead of the mostly used WAN port. To proceed with TP-link router setup and configuration a an access point, find the basic guidelines here:

Bind your Main router to the TP-link router over a LAN port utilizing an Ethernet cable.
Fasten your computer to a second available LAN port on which your TP-Link router is located, making use of the other Ethernet cable.

It is suggested to not try to attempt accessing the TP-link router as an access point over Wi-Fi network connection.

Get through TP-Link router login across a browser supported by your router model.
Get going to the web browser to browse tplinkwifi.net in the address bar. Tplinkwifi.net is the default login web address for TP-link router, default IP gateway is also an alternative approach to TP-link router login. For default gateway, you must address 192.168.1.1 as the IP address in the browser.
Begin with TP-link router login by entering the default tplinkwifi.net login details in the login page reached ahead of tplinkwifi.net login.
Fill in the essential TP-link router default information, which is supposedly “admin” in both the TP-link router login username as well as TP-link router login password tabs for reaching into the TP-link router’s web interface setup page.
You are directed to the TP-link router interface to follow TP-link router configuration as an access point for creating a WLAN connection.
Choose the Network option and opt for the LAN option on the side menu.
Convert the LAN IP address of your TP-Link router to IP address on the same segment of the main home network router.
Opt for Wireless on the same menu.
Access the Wireless Settings of your TP-link router and follow TP-link router configuration by configuring the wireless network name, SSID. It is entirely on you to create the same or different as for your main router.
You will also have to lay out the wireless security settings on screen.
Sort out the WPA/WPA2-as a security option by selecting them as it is thought to be the most secure wireless access point option.
Further, organize DHCP and configure the DHCP Settings. You will have to opt for Disable the DHCP Server option.
Choose the System Tools tab and hit on Reboot to reboot your model device.
Be patient while your TP-link router takes time to reboot and start over completing the configuration process over tplinkwifi.net login.
Bridge your Ethernet cable in between the main home network router and your TP-Link router at any of the 4 available LAN ports. This will permit all the other LAN ports on your TP-Link router as well to grant Internet access to the other wirelessly connected device.
This completes the TP-link router setup as an access point

You can then reconnect all your wireless devices to the new wireless local area network created across the TP-link router. Thus, setting up the TP-link router through TP-link router login over tplinkwifi.net login as an access point authorizes any Wi-Fi device of yours to access the wireless Internet network connection through your TP-Link router permitted over wireless network settings – the wireless network name SSID and Password inputting as you created and had set up above.

TP-link Router Setup Over tplinkwifi.net

Posted on December 18, 2020 by router

Prerequisites for Connecting to the TP-Link Wi-Fi Router wifi – TP-link router setup:

A Broadband Internet Access Service is essential for tplinkwifi.net access, possibly either over Ethernet network cable wire, DSL or Cable network connection.
A Cable or DSL Modem is a requisite too with a condition that it must have RJ45 connector if your TP-link router model is attached to modem with wired wire.
A Computer device is needed for directing TP-link router login and TP-link router setup across tplinkwifi.net, it must be connected to the router model employing an Ethernet cable or utilizing RJ45 connectors.
TCP/IP protocol should be functioning on the computer.
Accessible Internet Web browsers to direct Asus router setup through router.asus.com login.

Positioning TP-Link Wi-Fi Router ahead of TP link Router Setup:

Set your TP-Link Wi-Fi router in midway and open location of your house
Position your TP-link router in the setting that would cause minimal wireless signal interference from any surrounding metal, or concrete or magnetic objects.
Site your TP-link router on the floor to secure high wireless network signal strength from it.
Set your TP-link router in the zone that is devoid of any direct sun rays.

Installation of TP-Link Wi-Fi Router- TP-link Router Setup

Before you initiate TP-link router setup, you must be certain about your TP-link router being connected to the Internet network connection via broadband service as discussed earlier.

Turn out your previously connected modem, TP-link router &your computer by dowsing from power.
Set up your TP-link router model in the middle zone for proper wireless network signal.
Couple the TP-link router’s antennas to the provided ports in the upright direction and affix them pointing in all directions for uniform signal strength at all sides.
Bridge the computer to the TP-link router model adjoining them at one of the four given LAN ports of the TP-link Wi-Fi router utilizing an Ethernet cable.
Next, also link your modem to the TP-link router model adjoining it at the router’s given WAN port making use of another Ethernet cable.
Boot up all the connected devices – computer, TP-link router model and turn on.
Initiate the TP-link router setup directing tplinkwifi.net and router login details over web browsing.

TP-link Router Setup directed through tplinkwifi.net

Direct the TP link router login over the web browsing window using the login web domain www.tplinkwifi.net utilizing TP-link router login steps as explained below.
Perform TP-link router login process over the browser:

Get to the Internet Browsers on your Computer to reach through the TP-link router login with tplinkwifi.net.
Input the TP-link router login web protocol address www.tplinkwifi.net or default IP TP 192.168.1.1 n web browser address bar to site the TP-link router configuration page.
On the displayed login page, Enter the TP-link router default information – that is “admin” in both the username and password tabs for reaching into the TP-link router’s admin page.

Authorize the TP-link router Configuration for wireless network settings to connect using the wireless SSID/network name And the network key as required.
The TP-link router setup is completed following the router configuration of the network directed over tplinkwifi.net.

How to Change The Admin Username and Password of The TP-Link Device?

Posted on January 17, 2019 by router

TP-LINK is Chinese producer or manufacturer of computer networking products. The company’s notion was based on “twisted pair” link, which means a type of electromagnetic cabling; hence the company got its name “TP”.

TP-LINK PRODUCTS:

Wireless Routers
Mobile Phones
ASDL
Range extenders
Routers
Switches
Power banks
Power line adaptors
Print servers
Media adaptors, and many more devices.

LATEST NEWS IN TP-LINK

TP-LINK on 7th January 2019 has launched its new series of AX products powered by Broadcom’s 802.11ax (Wi-Fi 6) chipsets. The AX generation product launch includes routers, mesh WiFi systems and range extenders. These products are designed to provide fast WiFi as fast as greased lightning and are able to handle intensive bandwidth loads easily, making it the ideal solution for users who have a number of WiFi devices all over their home. Broadcom Inc. is a leading provider of WiFi/Bluetooth chipsets and is a trailblazer in Wi-Fi 6 technology.

TP-Link’s new Archer AX6000 is a dual-band wireless router that has similar features as that of the Archer AX11000. This new router also includes a 2.5Gbps WAN port so that if the user has a high-speed broadband connection, but does not use it to play games, then this router might be the most suitable router for the user because it costs $100 (approximately 6954 rupees) less than the price of Archer AX11000.

SOME COMMON ISSUES OF TP-LINK FACED BY USERS

How to change the admin username and password of the TP-Link device?

To change the admin username and password of your TP-Link WiFi routers. Open webpage tplinkwifi.net or tplinkwifi net you can follow either of the two examples given below depending on your model type:

Example A:

Click on Advanced > System Tools > Administration and finish the settings in the Account Management section.
Enter the old username and old password. Enter the new username and enter the new password twice (both the fields are case-sensitive). Click Save.

Example B:

Click on System Tools > Password on the left panel.
You will be now prompted to change your login information. Click on Save.
The system will redirect you back to the login screen. Enter the new username and password.

NOTE:

Before proceeding with the above steps it is assumed that the user has already logged on into TP Link’s web management user interface
This web management user interface varies from model to model

How can I know my actual Internet speed?

There are a variety of speed-test tools available online. You can try the most popular site: http://speedtest.net one drawback of this test is that it is Flash based and is not very accurate. For the more accurate test, you can go for HTML5 speed test like http://speedof.me.

I forgot my login password. How to recover it?

The default login credentials are both “admin”, until and unless you have changed. If you have changed it and cannot recall it then you need to reset your wireless router to factory default settings.

When your devices is running, press and hold the Reset button present on the rear panel with a pin or straightened paper clip for approximately 10 seconds.
After 10 seconds release the Reset button and wait for your router to reboot.
Make sure that your router’s power is on before it reboots.

How do I log in to my TP-Link Router?

Connect your WiFi router with the WiFi network.
Launch the Web browser from your computer or laptop and enter the IP address: 168.1.1, or 192.168.0.1 depending on the type of your router. The address for entering the settings is indicated on the bottom of the router.
You will be asked to enter the user name and password. The default is “admin” for both. In case you have changed these settings, then enter the new login credentials.
Now you might have successfully logged in to your TP-Link router settings.